2HP Dust Gorilla Portable Cyclone Dust Collector
Product Has Been Discontinued
Please contact us if you need additional support.
The Oneida's new Dust Gorilla Portable™ units offer flexibility and mobility not found in a fixed / central dust collection system. They collect dust very efficiently down to the smallest particle thanks to certified GE H12 HEPA filter media. They are manufactured in the USA and feature many of the design components found in our award winning & patent pending Smart Dust Collectors.
US Patent No. 8,491,686
|Filtration - GE H12 certified HEPA media Filter.||American Made Motor - Serviceable motor with grease fittings||Drum Full Strobe Light - Dust Sentry bin sensor flashes strobe light when dust barrel is full. Highly visible - alerts you from across the room.||Flame Guard Protection - Passive safety device to assist with OSHA compliance for industry.|
|Drop down 35 gallon steel dust barrel with castors. Easy dust removal and clearance to travel over electrical cords.||Patented V-Cyclone Technology - Higher efficiency fine separation than traditional cyclones.||Radio Frequency Remote Control - Long range, works through walls.|
6 Inch Dia. Inlet
95 Sq-Ft GE H12 HEPA media filter. 99.97% of 0.3 - 0.5 microns
Flame-guard protection - passive safety device to assist with OSHA compliance for industry
Footprint - 33" x 48"
Height - 76"
Noise Level - 73-74dB @ 10'
Power Supply - 208-240V Single-phase power. 60hz. 11.5 Amps
Cord - 14ga, 8 foot length. NEMA 6-20P Plug installed.
Maximum Static Pressure - 12" WC
|Motor Type||U.S. Baldor® TEFC Motor|
|Motor Service Factor||1.15|
|Recommended Breaker Size||20A|
|Power Connector||NEMA 6-20|
|Power Cord Length||10 feet|
|Impeller Type||Single-piece, backward inclined, non-sparking/non-ferrous, cast aluminum alloy.|
|Impeller Size||13" Dia.|
|Real CFM Rating||890 Actual CFM at 1.6" S.P.|
|Noise Level||73-74 dBA @ 10 ft|
|Filter Media Type||G.E. H12 HEPA|
|Filtration Efficiency||99.97% @ 0.3 microns|
|MERV Rating||MERV 16 ±|
|Total Filtration Area||95 sq ft|
|Waste Capacity||35 Gallon|
|Primary Build Materials||Cold Rolled Steel|
|Static Resistance Rating||Conductive (Metal)|
|Country of Manufacture||United States|
|Warranty Information||2 Year Limited Warranty|
|Contents||Blower Motor Assembly, Magnetic Starter, Remote Control, Fan Housing, Cyclone Separator, Filter Plenum, FlameGuard Cartridge Filter, Internal Silencer, Stand, 3x Wheels, Drum, 3x Drum Casters, Bin Level Sensor, Hardware|
|Applicable Patents||#7,247,180, #7,824,457, #8,377,160, #8,491,686, #8,496,719, #8,514,090|
|Inlet Size||6" Dia.|
|Height to Center of Inlet||55"|
No. This system is designed for use collecting dry materials only.
Yes but you will need to install a Machine Adapter into the inlet first. These adapters are smaller on the raw end than traditional ducting so that they can slip into the ports on systems and tools i.e. a 5" Quick-Clamp Duct Machine Adapter will measure ~4.9" O.D. on the raw end.
Oneida Air Systems' dust collectors are designed and tested for wood and wood dust. They can and have been be used effectively for various other dusts and chips such as drywall dust, paper dust, agricultural dust, metal chips and other forms of debris. The customer is however, cautioned that some common materials when cut, ground or processed by machinery may become very dangerous: highly toxic, flammable, or deflagrable and explosive and they should therefore ensure that you use your particular use of a dust collection system in accordance to national, state, local, NFPA, OSHA and all other applicable codes.