Actual appearance may vary to that shown above.

V-System 2000 Freestanding 35 Gal. Cyclone Dust Collector

  • Industrial 230V U.S. made fan motor provides ample CFM for 1 large tool with 4"-6" dust ports.
  • High efficiency cyclone (99%+ separation) with smooth, compound molded surface
  • Operates at ultra-quiet noise level, only 73dBA at 10 feet.
  • 3rd party tested, hospital-grade HEPA filtration with non-stick membrane for easy cleaning.
  • Durable, lightweight construction allows for quick and easy installation.

This Product Is Being Discontinued

Limited quantities available while supplies last. Please call 1-800-732-4065 to order or contact us if you need additional support.

Quiet, Compact, and Powerful - Ideal for Small Personal Workshops!

This system is designed to collect dust from 1 tool at a time (more if blast gates are used) and is ideal for use in small 1-2 man shops operating tools such as lathes, planers, radial/miter saws, and more!

The V-System's molded static conductive resin construction speeds up and simplifies system assembly, maximizes airflow performance, and significantly reduces noise levels.

Included Features & Components

  • Industrial 2HP U.S. Made Motor (230V)
  • Magnetic Starter w/ Overload Protector
  • High-Efficiency Molded Cyclone Separator
  • 3rd Party Tested HEPA Cartridge Filter
  • Patented Internal Foam Silencer
  • Compact Steel Angle Frame Stand
  • 35 Gallon Reinforced Fiber Dust Bin
  • D.I.Y. Ductwork Design Guide
  • 1 Year Limited Warranty

V-System Product Family Fan Performance Curve
OAS uses Actual CFM Ratings that reflect real-world airflow performance.

Continuously High Airflow Performance

Your dust collector should perform at peak efficiency at all times to ensure the health, safety, and quality of your work. That's why Oneida Air Systems uses only the highest quality motors with our dust collection systems. Far superior than the cheap, foreign imported motors used by other manufacturers, our industrial-grade motors are built to last a lifetime.

  • High-efficiency, U.S. made, Baldor® fan motor
  • Delivers up to 1,190 Actual CFM at 1.8" S.P. - ample airflow for any woodworking tool
  • Industrial-grade brushless motor designed for continuous duty
  • System's inlet and outlet rotate independently at 45 degree increments to suit your shop's needs.
  • Low pitch noise level provides ideal operator comfort
Closeup of V-System cyclone inlet

Streamlined Integrated Cyclone Separator

The V-System features an ultra-high efficiency cyclone which pre-separates up to 99% of fine dust and bulk debris, removing it from the airstream and collecting it safely below the cyclone.

  • Virtually eliminates filter clogging and suction loss to provide continuous suction performance.
  • Smooth, molded design reduces air turbulence to improve airflow performance and lower overall noise output.
  • 7" dia. neutral-vane inlet for use with common 6" ductwork layouts (reducers available).
  • Patented "V-Shape" cyclone design minimizes the system's overall height while maintaining airflow and separation efficiency.
  • Significantly extends the lifespan of the filter and reduces downtime needed for cleaning.
V-System Filter and Plenum

High Quality & Serviceable Filtration

The V-System system uses hospital-grade, G.E. Certified H12 HEPA media cartridge filters that are specifically designed for dust collection applications - providing unbeatable airflow and filtration performance.

  • OAS fully stands by the quality and performance of our filters; each filter is sent to an accredited independent testing lab. Conact us for more information and documentation.
  • Patented internal acoustic foam reduces noise caused by vibrating outgoing air by 1–2 dBa
  • Patented Flame Guard™ safety mesh rapidly dissipate any heat generated by a deflagration within your filter, helping to comply with future planned NFPA fire safety codes.
  • Fine dust pan captures residual dust that falls off the inside of the filter. Can be removed easily for cleaning after reverse blowing compressed air into the pleats.
V-System Stand

Compact, Configurable Design

This unit is equipped with a Freestanding Leg Kit and has been built specifically to fit underneath standard 8ft ceilings; perfect for garage or basement shops!

Motor TypeU.S. Made TEFC Motor
Motor Service Factor1.15
Recommended Breaker Size15A
Amperage (Typical)11.5A
Phase (Pre-Wired)1-Phase
Power ConnectorNEMA 6-20
Power Cord Length10 feet
Impeller TypeSingle-piece, backward inclined, non-sparking/non-ferrous
Impeller Size13" Dia.
Real CFM Rating1,190 Actual CFM at 1.8" WC
Maximum Suction11" WC
Noise Level73 dBA @ 10 ft
Filter Media TypeG.E. H12 HEPA
Filtration Efficiency99.97% @ 0.3 microns
MERV RatingMERV 16 ±
Total Filtration Area95 sq ft
Waste Capacity35 Gallon
Remote ControlIncluded
Primary Build MaterialsSD Polyethylene
Static Resistance RatingStatic Dissipative
Inlet Size7" OD
Outlet SizeSquare ID: 7-3/8"(W) x 6-3/8"(H)
Discharge Size7" Dia.
Height to Center of Inlet63" w/ 35 Gal. Stand
75" w/ 55 Gal. Stand
ContentsBlower Motor Assembly, Magnetic Starter, Fan Housing, Filter Plenum, FlameGuard Cartridge Filter, Freestanding Leg Kit, Fiberboard Dust Bin, Internal Silencer, Cyclone Separator, Remote Control, Hardware
Country of ManufactureUnited States
Warranty Information1 Year Limited Warranty
CertificationsComplete system is cETLus certified for indoor use
Applicable Patents#7,247,180, #8,377,160, #8,496,719
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account
Frequently Asked Questions
How often should I clean the dust collector's cartridge filter?

This can vary widely depending on how often your dust collector is used and what kind of dusts it's exposed to but you should typically clean it only once you've noticed a considerable drop in suction performance. In our experience this can be around once per year, but with heavy amounts of sanding it could be as often as once per month.

A meter such as our Filter Efficiency Gauge can also be used to monitor pressure buildup and inform you when the filter need's to be cleaned.

What is the floor space required for the V-1500 w/ 35 gallon drum?

On the floor, the V-System's stand is a 30" x 30" square. How wide the overall system is depends on the orientation of your filter plenum. If the plenum is oriented ninety degrees clockwise from the system's inlet, then the overall width would be 47". Please refer to the owner's manual for more detailed dimensions.

Can it be used with a smaller dust bin to lower the total height to 80”

With the stand, the V-System's overall height cannot be lower than 87" (for 1.5HP) or 88" (for 3HP). Oneida Air Systems does offer wall-mounting brackets for the V-System, available by phone order only. This would allow you to mount the V-System dust collector at a lower height for use with smaller containers. Please note that you may have to empty the smaller drum much more frequently depending on your workflow.

What do I need to know about NFPA regulations?

Fire protection regulations are a complex and ever-changing set of rules that differ from facility to facility. Click the "read more" link to review our Best Practices for Dust Collection Fire Safety or contact us for more detailed assistance.

  California Residents: Please visit for information regarding Proposition 65 for our products.

Oneida Air Systems (OAS) is not responsible for typographical errors, omissions, or other clerical errors that may occur and makes every effort to provide the most detailed and accurate information available regarding our products. If you encounter incorrect information, please contact us. OAS reserves the right to restrict quantities and correct prices when necessary.