Dust Deputy Deluxe Cyclone Separator Kit
|Airflow Rating||50 - 150 CFM|
|Waste Capacity||5 Gallon|
|Inlet Size||2" O.D. (Tapered)|
|Outlet Size||2" O.D. (Tapered)|
|Height to Center of Inlet||25.125"|
27.125" w/ casters
|Primary Build Materials||Polyethylene|
|Static Resistance Rating||Anti-Static|
|Contents||Cyclone, Pre-Cut Bucket, Sidecar Bucket, Caster Wheels, Hose, 2x Elbow Adapters, Hardware|
|Country of Manufacture||United States|
|Warranty Information||1 Year Limited Warranty|
|Applicable Patents||Patent #7282074, #6833016|
The Dust Deputy can be used with any make, model, or size wet/dry vacuum. We recommend that it has an airflow rating of at least 50 CFM to ensure optimum dust separation performance.
No. The smaller Dust Deputy cyclone are intended for use with HIGH pressure and LOW airflow systems, such as wet/dry vacuums, with port sizes 2.5" diameter and smaller. It would not be suitable for your HIGH airflow, LOW pressure system (i.e. dust collectors...
It is 30.75" to the very top of the tapered elbow fitting on the Dust Deputy Deluxe (with a single bucket and no casters).If you are requesting this measurement to fit the product underneath a table, or into a custom built cart, we recommend leaving ...
There is very little difference between the two versions of the Dust Deputy Deluxe. The primary difference is that the "A" model contains higher-end, static conductive, hose components to prevent electrical charges from building up and discharging. See table below for more details:
|Hose Length||5-1/2 feet||3 feet|
|Hose Material||Static Dissipative||Static Conductive|
|# of Hose Elbows||x1||x2|
|Hose Elbow Material||Static Dissipative||Static Conductive|
Oneida Air Systems no longer produces the older #AXD000004 model, but some may still be sold online through other retailers (Woodcraft, Amazon, Ebay, etc.).
The hardware (gasket, nuts, bolts,etc.) is stored in between the two buckets included in the kit.
You'll want to apply the tape so that all three openings on the cyclone are connected by a conductive path. When doing so, make sure that the tape is wrapped over the edge of the cyclone's ports and that it overlaps the bolt hole on the cyclone's bottom flange.
- Apply tape over the edge the cyclone's outlet by 1/4".
- Run tape down the outlet, across the top of the cyclone, and down the side of the cyclone.
- Make sure that the tape overlaps a bolt hole on the cyclone's bottom flange.
- Apply tape over the edge of the cyclone's flange by 1/4".
- Cut the remaining tape off.
- Apply second portion of tape over the edge of the cyclone's inlet by 1/4"
- Connect the second portion of tape to the first, making sure that they overlap with eachother.
- Smooth down any wrinkles in the tape so that it all lies flat against the surface of the cyclone.
- When mounting the cyclone to your dust bin's lid, the washers should rest directly on the conductive tape where it was run over the bolt in step 3.
In most cases, yes - but the cyclone's efficiency will vary based on whether your vacuum is also turned on.
The Dust Deputy cyclone needs a consistent airflow rate to "spin" the dust out of the airstream; If your tool's fan blower is pushing air in while your vacuum is also sucking air out, this can disrupt the airflow rate and reduce the cyclone's separation performance.
In many cases, the fan blower on tools (such as planers) cannot be turned off. If that is the case for you, try collecting your dust with the vacuum turned off. In doing so you will be creating a positive pressure system as the tool's fan blower pushes air through the Dust Deputy cyclone. This method may not work with every vacuum
Even a small leak can significantly affect the overall separation performance of the cyclone. Here are some common places where leaks may occur:
- Along the lid of the dust bin
- Hose adapter fittings on the cyclone
- Where the cyclone is mounted to the lid
- Along the length of your hose
If you can't audibly pinpoint where the leak might be coming from, one of the simplest ways to check for air leaks is with a smoke test. Kits for this can be found at most local hardware stores (usually near the HVAC sections), but it's simple to make a small DIY version or even use incense sticks at home.
With the shop vacuum turned on, simply carry the smoke-stick along the perimeter of your cyclone system and check for where the smoke is drawn into the cyclone. That will show you where your air leak is.
No. This cyclone is designed for use with light debris such as wood dust. For heavy-duty applications with highly abrasive or smoldering materials, we recommend our steel, Heavy-Duty Dust Deputy kits instead.